HOMECONTACThygradeothertestimonials

Hygrade Graders - Models 800, 1000, 800RS, and 1000RS

Model 1000 shown

The HyGrade design with the farmer in mind

Models 800, 800RS, 1000, and 1000RS have:

  1. All hydraulic cylinders, hoses, and tips are included.
  2. All hydraulic cylinders have nitro steel shafts.
  3. Available in 8' and 10' blade lengths.
  4. Blade tilts 15 degrees left and right for slope cuts.
  5. Blade angles 40 degrees left and right
  6. On Models 800/1000, all three hydraulic functions can operate from one remote.
  7. Models 800RS/1000RS require one additional remote to operate rear steer functions.
  8. Concrete weight, box scraper ends are standard with each model.
  9. Reversible / replaceable high carbon steel cutting edge.
  10. Deep Tri Rib tires have excellent side bite traction.
  11. Excellent blade to ground clearance.
  12. Storable hitch jack.
  13. Safety chain is included.
Model 1000HDRS and Model 1000RS shown
Specifications
MODEL 800 1000
Blade Blade Length 8' 10'
  Blade Angle 40° 40°
  Blade Height 17" 17"
  Blade Tilt 15° 15°
  Blade to Ground Clearance 15" 15"
Tires   Two Tri Rib 5.00 x 15", 4 ply Two Tri Rib 5.00 x 15", 4 ply
Hubs and Spindles   1500# 4 bolt 1500# 4 bolt
Total Weight   1880# 1960#
Tongue Weight   480# 550#
Transport Width   7' 1" 8' 10"
Cutting Width at 40° Angle   6' 5" 7' 11"
Overall Length   16' 2" 16' 2"
HP Range   25 - 100 25 - 100

ALL THREE HYDRAULIC FUNCTIONS CAN OPERATE FROM ONE REMOTE.

Models 800 and 1000 come equipped with one of the following three options:

3 button handle
(operates off of one remote)
3 switch control box
(operates off of one remote)
6 hoses
(for tractors with 3 remotes)

Models 800RS and 1000RS HyGrade Grader / Box Scraper

Model 1000RS
Model 1000RS with box ends tipped
down to convert to a box scraper
Swivel hitch for Models 800, 800RS, 1000, and 1000RS

 
1000RS steered to the right
1000RS steered to the left

The models 800RS and 1000RS have Hydraulic Rear Steer that allows the operator to move the blade approximately 3 feet more to the left or the right side of the tractor. All done hydraulically from the tractor seat.
These Rear Steer models require a minimum of 2 hydraulic remotes.

This rear steer feature allows the HyGrade Grader to clean among bunk lines, feedlot fences, in poulrty barns, around buildings, road edges, trees, etc. without having to drive the tractor so close to the objects that you are working near.

The Rear Steer feature gives the grader the capability to clean out drainage or irrigation ditches that are wet, while keeping the tractor on dryer ground. The Rear Steer models are very useful in orchards where reaching under trees is necessary.


Specifications
MODEL 800RS 1000RS
Blade Blade Length 8' 10'
  Blade Angle 40° 40°
  Blade Height 17" 17"
  Blade Tilt 15° 15°
  Blade to Ground Clearance 12" 12"
Tires   Two Tri Rib 5.00 x 15", 4 ply Two Tri Rib 5.00 x 15", 4 ply
Hubs and Spindles   1500# 4 bolt 1500# 4 bolt
Total Weight   2160# 2240#
Tongue Weight   520# 590#
Transport Width   6' 8" 8' 5"
Cutting Width at 40° Angle   6' 5" 7' 11"
Overall Length   18' 18'
HP Range   25 - 100 25 - 100

To operate the functions of blade angle, tilt, and lift;
Models 800RS and 1000RS come equipped with one of the two following options:

3 Switch Control Box
(operates off of one remote)
3 Button Handle
(operates off of one remote)


A second remote is required for the rear steer functions

See Our 10'HD, 12', 14' & 16' Hygrade Graders